;//senior 8bit settingTL0=(65536-50000)%256;//junior 8bit settingEA=1;// superior inter onET0=1
2017-04-17 13:20
the superior specs of the 16850, why should I even consider getting the 16800? Is the 16850 limited
2018-12-18 16:09
你好， 这两个模块有什么区别？ 为什么DLC如此昂贵？＃lsm330＃lsm330＃lsm330dlc以上来自于谷歌翻译以下为原文 Hello, what is the difference between these two modules? Why DLC is so much expensive?#lsm330 #lsm330 #lsm330dlc
2018-11-15 10:55
亲爱的朋友，我用的是Sparten 6 LX75T。根据xilinx的PCB设计和PIN规划指南文件，他们提到VCC INT的电容器和所有其他电源的电压都非常低。我正在研究ALTERA产品，我通过PDN工具计算了许多用于相同电流和电源和逻辑的耦合电容器。那么为什么Xilix FPGA Sparten 6需要的耦合电容更少？亲切的问候，Sameer以上来自于谷歌翻译以下为原文Dear Friend, I use Sparten 6 LX75T. According to PCB design and PIN planning guide document by xilinx, They mentioned very less capacitor for VCC INT and all othersupply volatage . I was working on ALTERA product befor , i calculatedmany Coupling capacitors by PDN tool for same current and supply and logic. So Why do Xilix FPGA Sparten 6 need very less coupling capacitor ?Kind Regards,Sameer
2019-06-03 07:03
device which is positioned in the same range (I understand the Spartan 6 is a superior device
2019-04-12 14:45
亲爱的所有人，我目前正在使用双音测试对滤波器进行IMD测量。我正在使用两个独立的信号发生器来做到这一点。我正在为此目的使用两台Agilent E4422B发生器。 1）但我想为此目的使用两个33250A发生器。我怎么知道这个发生器给出的失真是更差还是更好？.2）一般来说，如果我想比较两个不同的信号发生器在IMD测量中的使用，比较的步骤/方法是什么他们。？。我有什么需要照顾的事情？.Regards，Lokesh 以上来自于谷歌翻译 以下为原文Dear All,I'm currently taking IMD measurements for a filter using two tone test. I'm using two separate signal generators to do that. I'm using two Agilent E4422B generators for this purpose. 1)But I want to use two 33250A generator's for this purpose. How will I know whether the Distortion given by this generator will be worse or better?.2)In general, If I want to compare two different signal generator for using in an IMD measurement, What are the steps/methods to be followed for comparing them.?. What are the things that I have to take care of?.Regards,Lokesh
2019-05-13 10:09
technical reason why most PCBs are green. 2. Green solder mask is physically superior Due
2018-09-14 16:00
format, the data rate would be far superior. Problem is sensor outputs a raw10 format and so
2018-09-07 14:52
如何提高FATFS SD性能？
2022-02-11 06:28
我使用CY8CKIT04942XX，我试着用表面电极测量肌肉的冲动。我已经设法得到某种信号，但它工作不一致，ADC的直流电平不同于运行到运行。有时我能看到清晰的信号，有时什么也看不见。当它工作时，信号的直流约为0，信号跳跃在10-20MV左右，当它工作不良时，它跳到50MV和0之间，很难得到任何粘结剂，有时尖峰到1024（可能是由于坏的USB连接）。我想知道在我的设计中是否有缺陷或者我使用这个设备的方式，或者是因为连接和噪音的不良吗？我已经附加了项目文件夹。顶部设计中的寄存器显示当前没有使用任何东西，它们只是未来的占位符。溴Joona RCydSn.Zip1.8兆字节 以上来自于百度翻译 以下为原文I'm using CY8CKIT 049-42xx and I'm trying to measure muscle impulses with surface electrodes. I have managed to get some kind of signal, but it is working inconsistently and dc level of the adc is different from run to run. Sometimes I can see a clear signal, sometimes nothing at all. When it works, the dc of the signal is around 0 and signal jumps around 10-20mV, when it works badly it jumps between 50mv and 0 and it's hard to get anything cohesive out, sometimes spiking to 1024 (possibly due to bad u*** connection). I am wondering if there are flaws in my design or the way I'm using the device or is this due to bad connection and noise? I have attached the project folder. The registers show in top design aren't currently used for anything, they're just placeholder for future. Br Joona R adctesting.cydsn.zip 1.8 MB
2018-12-04 14:47
