• 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
返回

电子发烧友 电子发烧友

  • 全文搜索
    • 全文搜索
    • 标题搜索
  • 全部时间
    • 全部时间
    • 1小时内
    • 1天内
    • 1周内
    • 1个月内
  • 默认排序
    • 默认排序
    • 按时间排序
  • 全部板块
    • 全部板块
大家还在搜
  • 求助!步进电机上电没反应也没声音?

    两相四拍步进电机(NMB-MATPM-35L-048-YSG8),驱动芯片为SANYO的LB1848。有的时候通电没有反应,电机不转动也没有声音,要开几次开关才可以。但是有的时候是运转正常。上电也加了延迟。

    2017-09-07 17:06

  • L6470采用UNIPOLAR MOTOR

    我使用ST L6470和单极电机。    L6470是双极型驱动器,所以我没有连接单极电机的com线。  电机规格如下:  MAKER:sanyo denki  型号:103H5210-0480

    2018-11-26 09:20

  • 求助!为什么步进电机开两次开关才转动?

    两相四拍小步进电机,驱动芯片为SANYO的LB1848。步进电机总是需要开两次开关才转动,有时候开一次就转的话就不按照程序走。求助大神,刚开始学习步进电机。

    2017-08-30 11:18

  • 电解电容廉价替代方案(寻找红宝石电容替代品)

    大家好公司boss让我论证一下红宝石电解电容的替代,主要是为了降低成本。请问这个器件有合适的替代品么,要做一些必要的验证么?多谢

    2019-04-27 08:30

  • 保持期间的绕组噪音

    你好, 使用L6472时,我听到电机在听到时会发出声音(高音)噪音。 噪声量随着保持电流的增加而增加。电机是否装载无关紧要。当我查看带有示波器的绕组时,典型的pwm信号锁定和占空比适合保持设定值另一对绕组看起来“解锁”,频率比其他绕组高得多。 EVAL Bd硬件 24v电源,电流设定点.35amp Nema17,18mh / 8.9ohms,0.9度步进角有一个我忽略的环境L6470不会发生这种情况。 感谢您的支持 !以上来自于谷歌翻译以下为原文 Hello, With L6472 I hear audible (high pitch) noise from motor when holding. volume of noise increase with increase hold current. It does not matter if the motor is loaded or not.When I look at winding with scope one pair is the typical pwm signal locked and duty cycle appropriate for the hold setpoint The other pair of windings appear ‘unlocked’ and much higher in frequency than the other winding. EVAL Bd hardware 24v supply, current set point .35amp Nema17, 18mh / 8.9ohms, 0.9degree step angleIs there a setting I am overlooking This does not occur with L6470. thanks for your support !

    2019-03-26 10:50

  • 如何用PSoC 5LP串并联液晶转换器?

    ,as well, I have got raw serial data from sanyo LC7981 LCD controller FLM:A pulse on this line resets

    2019-07-30 10:00

  • 关于利用液晶显示器制作三次元立体影像技术动向你想知道的都在这

    本文将介绍有关利用液晶显示器制作三次元立体影像技术动向。

    2021-06-08 06:48

  • L6470移动到一个位置然后反向时会短了2或3步

    我们在新设计中使用L6470。我们发现当我们移动到一个位置然后反向时,我们发现新位置短了2或3步。在此初始化错误之后,所有未来在同一方向上的移动都是正确的。如果方向再次反转,我们会在第一步中再次失去2或3个步骤。我们在步进轴上安装了一个编码器,确认了这一动作。我们还在皮带上放了一个百分表,并确认我们确实错过了这两个或三个步骤。 ST工程师请求回复,因为我们没有关于如何解决这个问题的想法。以上来自于谷歌翻译以下为原文 We are using the L6470 in a new design. We have found that when we move to a position then reverse direction we find that the new position comes up short by 2 or 3 steps. After this initail error all future moves in the same direction are correct. If the direction is reversed again we lose the 2 or 3 steps again on the first move. We have an encoder mounted on the stepper shaft which confirms this action. Also we have placed a dial indicator on the belt and confirmed that we are indeed missing these 2 or 3 steps. ST engineers pleas reply as we are out of ideas on how to fix this issue.

    2018-12-26 16:20

  • 无线充电的实现方式是什么?

    利用物理学的“共振”原理——两个振动频率相同的物体能高效传输能量。

    2020-04-08 09:01

  • 伺服电机是指什么?伺服电机与步进电机的使用性能有何不同?

    伺服电机是指什么?其主要特点是什么?伺服电机与步进电机的使用性能有何不同?与其他电机(如步进电机)相比,伺服电机的优点是什么?

    2021-06-28 07:16