嗨，我在哪里可以获得与VMware vSphere 6.5兼容的Tesla M60 .vib文件/驱动程序？任何帮助都感激不尽。先谢谢你。干杯，灰以上来自于谷歌翻译以下为原文Hi, Where can i get VMware vSphere 6.5 compatible Tesla M60 .vib file/drivers ?Any help will be much appreciated. Thank you in advance. Cheers,Ash
2018-09-27 15:59
关于服务器支持的快速问题。惠普或IBM等英特尔服务器是否会在全球范围内提供支持？像快速响应时间和易于更换。我假设是的，因为它是英特尔，但我不确定。以上来自于谷歌翻译以下为原文Just a quick question about server support. Is there support around the world for Intel servers such as HP or IBM will have? Like fast response time and easy replacement. I assume yes because it is Intel, but I do not know for sure.
2018-10-23 10:41
当我收到NUC时，它最初是在安装了两个模块的情况下启动的，但是当我使用虚拟机时它就冻结了。我运行了一个失败的内存测试...然后我单独测试了模块，他们通过了各个测试.NUC会然后没有安装两个模块启动。我注意到我有不同的内存速度1 x 2133 MHz和1 x 2400 MHz。一个模块换掉后，我仍然遇到同样的问题。当NUC有2 x 16GB Transcend内存模块（2133 MHz）发生以下情况：-NUC启动......但是没有任何东西出现在displayNUC关闭它自己的NUC然后自己启动只能再次关闭并重复上述过程。我还有一个问题......我看看Transcend 2400 MHz内存模块已经过测试/批准用于我的NUC ???为什么你使用2400 MHz模块时，在规格表中说明内存是DDR4-SO-DIMMS 2133MHz以上来自于谷歌翻译以下为原文When I received the NUC, it originally booted with both modules installed, but then froze when I was working with virtual machines.I ran a memory test which failed … I then tested the modules individually, and they passed the individual tests.The NUC would then not boot up with both modules installed.I then noticed that I had disparate memory speeds1 x 2133 MHz and 1 x 2400 MHz.After having the one module swapped out, I am still experiencing the same issue.When the NUC has 2 x 16GB Transcend memory modules (2133 MHz) the following happens:-NUC powers on … but nothing appears on the displayNUC shuts down on its ownNUC then powers up on its ownOnly to shutdown again and repeat the above process.A further question I have … I see Transcend 2400 MHz memory modules have been tested / approved for my NUC ??? why are you using 2400 MHz modules when it is stated in the spec sheet that the memory is DDR4 - SO-DIMMS 2133MHz
2018-10-23 10:38
亲爱的社区，我用两周就使用了INTEL Nuc Intel Core i7-7567U（代码NUC7I7BNHX1）。我的nuc通过HDMI线连接到显示器。我注意到随机屏幕变黑了几秒钟，然后再次显示图像。我推出了所有驱动程序和BIOS（这里附有一份报告），但问题还在继续。说实话，它似乎比以前更糟糕了。有什么建议么？最好的祝福安东尼奥Detailed-System-Report.html.zip 2.7 K.以上来自于谷歌翻译以下为原文Dear community, I'm using aINTEL Nuc Intel Core i7-7567U (code NUC7I7BNHX1) since a two weeks.My nuc is connected to a monitor by using an HDMI cable.I noticed that randomly the screen become black for few seconds and than the image is shown again.I uptodated all the drivers and the BIOS (here attached a report) but the problem continues. To be honest, it seems that it is worst than before now.Any suggestions? Best regardsAntonio Detailed-System-Report.html.zip 2.7 K
2018-10-26 14:54
目前,各类伺服驱动器及其应用中广泛采用光栅装置作为速度测量、位置测量的敏感元件。而且,广泛采用两路正交方波的形式,系统的实时性要求极高。因此,对于光栅编码器的信号的细分等主要处理环节,一方面集中考虑提高分辨率的问题,同时,需要考虑实时性的问题。
2019-10-30 06:12
