• 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
返回

电子发烧友 电子发烧友

  • 全文搜索
    • 全文搜索
    • 标题搜索
  • 全部时间
    • 全部时间
    • 1小时内
    • 1天内
    • 1周内
    • 1个月内
  • 默认排序
    • 默认排序
    • 按时间排序
  • 全部板块
    • 全部板块
大家还在搜
  • L6472步进驱动器布局需要使用4层PCB吗?

    that requires a 4 layer PCB with the L6472 device?Would you foresee any issues if I roll my own L6472

    2018-10-19 11:17

  • 独立的HW Server怎么安装

    foresee the need to have the entire Xilinx Toolset on the machine that is near my FPGA board. I would

    2018-12-11 11:24

  • 哪个版本的TestExec可以与哪个版本的VEE一起使用?

    您好,哪个版本的TestExec可以与哪个版本的VEE一起使用?是否有某个表格包含两个程序的所有版本?在我的情况下它是:目前我正在使用TestExec 4.1和Vee 6.01我可以将TestExec更新到6.1.2并仍然使用Vee 6.01?或者我还必须更新vee版本?谢谢 以上来自于谷歌翻译 以下为原文Hello, which version of TestExec can be used with which version of VEE? Is there somewhere a table with all versions of the two programs? In my case it is: Currently i am using TestExec 4.1 and Vee 6.01 Can i update TestExec to 6.1.2 and still use Vee 6.01? Or do i also have to update the vee-version? Thanks

    2019-01-11 16:14

  • 如何断开SPI信号而不拧紧其他电线?

    我想演示使用Harmony和以太网启动器套件II(PIC32MX处理器)的单向三线处理器间通信。在我掉进黑洞之前,有没有人做过这样的事情,或者告诉我它会或不会工作?我相信SPI有一个主模式,输出3个信号(SDO,SCK,SS),但如果SDI信号没有连接,和谐SPI驱动程序会工作吗?以太网启动器套件II有一个120引脚连接器,所以我打算买一个第二板,2个连接器和一个电缆。希望我能找出如何断开SPI信号而不拧紧其他电线。这样行吗?提前感谢。… 以上来自于百度翻译 以下为原文I would like to demonstrate a one-way 3-wire interprocessor communication using Harmony and the Ethernet Starter Kit II (PIC32MX processor).Before I fall into a black hole, has anyone done something like this or can tell me that it will or will not work? I believe SPI has a master mode that outputs 3 signals (SDO, SCK, SS) but will the Harmony SPI driver work if the SDI signal is not connected? The Ethernet Starter Kit II has a 120-pin connector so I was going to buy a second board, 2 connectors and a cable.Hopefully I can figure out how to disconnect the SPI signal without screwing up the other wires.Will that work? Thanks in advance . . .

    2019-07-02 09:35