您好，最新版本1.5.1.0的Agilent GUI数据记录器在U1253A上无法正常工作。连接DMM后，如果使用位于ACV或DCV的****开始记录，则图表会更新，但不会更新数据表。如果在记录时将****切换为Resistance，则表开始更新，如果返回DCV，数据表将停止更新。此外，如果按下shift按钮并再次按下它并将****切换到不同的位置，则功能和单位不会更新，尽管测量的值是正常的。我希望你能尽快解决这些问题。谢谢 以上来自于谷歌翻译 以下为原文Hello, The last version 1.5.1.0 of Agilent GUI Data logger does not works fine on U1253A. After connecting with the DMM, If you start logging with the **** located at ACV or DCV, the graph is updated BUT NOT the Data Table. If while logging you switch the **** to Resistance, the table starts to update, if you go back to DCV, the data table stops updating. Also, if you press shift button and press it again and switch the **** to different possitions, the functions and units are not updated, although values measured are ok. I hope you can fix these issues soon. Thanks
2019-08-21 13:26
您好，我有一台U1253A万用表，我在2009年购买。几个月前，我注意到OLED显示屏的亮度已经大大降低到在正常室内光线条件下几乎看不到读数的程度。我可以尝试将亮度调整到中等或最高水平，但没有任何明显的变化。在低电平时，显示亮度非常低，在任何实际情况下都没有用。我想知道在哪里可以发送DMM以便在阿根廷提供服务。非常感谢你。安德烈斯 以上来自于谷歌翻译 以下为原文Hello, I have a U1253A multimeter that I bought in 2009. A couple of months ago, I noticed that the brigthness of the OLED display notoriously decreased up to a point that the readings can be hardly seen at a normal indoor light condition. I can try to adjust the brightness to mid or maximum level,but there is not any noticeably change. In low level, the display brightness is really low, and not usefull in any practical situation. I would like to know where can I send the DMM to get it serviced in Argentina. Thank you very much. Andrés
2019-03-07 08:13
你好，我想知道下面的引脚有内部拉升或下降寄存器；塔皮塞尔杰塔格塞尔UB2SDSL海波尾流海比尔皮塞尔我相信下面的引脚已经下拉；异步模式WBPUBoT模式GPIOI9（UBSSESEL）GPIOE13（SDIOOI模式）GPIOIG1（GSPIX模式）先谢谢你。哈里森 以上来自于百度翻译 以下为原文Hello, I want to know the following pins have internal pull up or down registers; TAP_SEL JTAG_SEL USB2_DSEL HIB_WAKE HIB_LPO_SEL I believe the following pins have pull down; ACPU_BOOT_MODE WCPU_BOOT_MODE GPIO_9(USB_SEL) GPIO_13(SDIO_MODE) GPIO_1(GSPI_MODE) Thank you in advance. Harrison
2018-11-07 17:02
尊敬的各位专家， 你们好， 目前我是在CCS5环境下，向OMAPL138中加载nand-writer_ccs33.out程序。进入debug模式后，560v2仿真器找到C674X，PRU_0，PRU_1，以及ARM9处理器，接连ARM9处理器时，出现以下错误提示： ARM9_0: Output: Memory Map Cleared. ARM9_0: Output: --------------------------------------------- ARM9_0: Output: Memory Map Setup Complete. ARM9_0: Output: --------------------------------------------- ICEPICK_C: Trouble Writing Memory Block at 0x1c14038 on Page 0 of Length 0x4 ARM9_0: GEL: Error while executing OnTargetConnect(): Attempted to write unmapped virtual memory at 0x01C14038 at *((unsigned int *) (0x01C14000+0x038))=0x83e70b13 [OMAPL138_ARM.gel:201] at DEVICE_kickUnlock() [OMAPL138_ARM.gel:244] at OnTargetConnect() 之后，加载nand-writer_ccs33.out程序，运行，打印信息为[ARM9_0] Starting DA8xx_NANDWriter。 注：nand-writer_ccs33.out是合众达提供的CCS3.3环境下的烧写程序，加载后会弹出对话框提示选择需要烧写的文件路径，而CCS5环境下加载该程序只会再控制台显示打印信息，需要手动输入被烧写文件的路径。 请问问题出在哪里？劳烦抽空解答，非常感谢。
2018-06-21 04:53
